狂躁美女大bbbbbb视频u,少妇愉情理伦片丰满丰满,精品国产粉嫩内射白浆内射双马尾,日韩精品一区二区三区视频

產品展示
清遠碳化鎢輥

清遠碳化鎢輥

  • 所屬分類:清遠碳化鎢輥
  • 瀏覽次數:
  • 二維碼:
  • 發布時間:2022-03-14 10:47:25
  • 產品概述
  • 產品特點
  • 產品參數



工序號

Number

工序內容

Process

相關照片

Photos

檢測設備

Test

1-1

檢查工件表面是否有震紋,斜紋,磕碰、砂眼、孔洞等。

Check whether the roll surface has shock, twill, bump, sand hole, hole, etc.

目測

Visual measurement

1-2

檢查工件尺寸等是否符合技術要求?

Check whether the size of the roll meets the technical requirements in drawing?

 

 

 

卡尺、外徑千分尺

Calipers and Micrometer


工序號

 

工序內容

Process

相關照片

Photos

檢測設備

TEST

2-1

1.工件吊裝至專用旋轉工裝上,進行除濕去油處理。

2.除濕時工件必須旋轉進行。

1. Lift the roll to the special rotary tooling for dehumidification and oil removal.

2. The roll must be rotated during dehumidification.

設備型號 ;JP5000不送粉



2-2

工件轉數 ;:查轉速表

烘烤時間; 自動走一個來回

烘烤溫度;去除水份,表面干燥。

清洗劑種類;專用清洗劑

Revolution: check the tachometer

Baking time: automatic walk back and forth

Baking temperature: remove moisture and dry the surface.

Cleaning agent type: special cleaning agent




序號

 

工序內容

Process

相關照片

Photos

檢測設備

TEST

3-1


噴砂使用的空氣由壓縮機出來需要經過冷凝器與濾清器過濾。每次使用前需用白紙進行檢測(方法:壓縮空氣對白紙吹1分鐘,距離100~150mm,觀察是否有水分或油污)。


 

The air used for sandblasting is filtered by condenser and filter when it comes out of compressor. White paper shall be used for detection before each use.

The method is as follows: blow white paper with compressed air for 1 minute, with a distance of 100-150 mm, and observe whether there is water or oil stain.


3-2

噴砂設備:壓力式全自動噴砂機

噴槍:1

噴砂角度:60°-90°

噴砂材料:白剛玉

噴嘴直徑:6-7

噴槍距離:200-250

噴砂空氣壓力0.45~0.75Mpa

 

 

Sandblasting equipment: pressure type automatic sandblasting machine

Spray gun: 1

Sandblasting angle: 60 ° - 90 °

Sandblasting material: white corundum

Nozzle diameter: 6-7mm

Spray gun distance: 200-250mm

Sand blasting air pressure is 0.45 ~ 0.75mpa

 

 


3-3

 

噴砂后的檢驗:

1. 使用壓縮空氣吹干凈工件表面。

2. 噴砂后表面清潔度達到ISO 8501 Sa3。

3. 按照技術要求使用粗糙度儀進行測量,滿足輥面成品決定粗糙度大小。

Inspection after sandblasting:

1. Use compressed air to blow clean the workpiece surface.

2. The surface cleanliness after sandblasting shall reach ISO 8501 SA3.

3. Use roughness meter to measure according to the technical requirements, to meet the requirement that the roughness of the finished roll surface is determined.

 


 

ISO 8501 Sa3

清潔度圖片

粗糙度儀

Roughness tester





序號

 

工序內容

Process

相關照片

Photos

檢測設備

TEST

5-1

1.噴涂后的輥筒吊裝至專用大型拋磨機床上進行去峰處理。

2.拋加工時必須使用專用拋光帶進行處理。

3.滿足圖紙粗糙度要求。

4.進行粗糙度的測量及記錄。

 

 1. After spraying, the roller is hoisted to the special large grinding machine for peak removal.

2. Special polishing belt must be used for polishing.

3. Meet the roughness requirements of drawings.

4. Measure and record the roughness.

千分表、粗糙度儀

Dial indicator and Roughness tester

5-2

 

粗糙度儀型號:

Roughness tester:

MITUTOYO SJ-301

 



5-3

噴涂完成后,必須確保涂層面無污染。

采用專用封孔劑對無污染的涂層面進行封孔處理。

待漆膜干固后進行二次封孔處理。

After spraying, the coating surface must be free of contamination.

Special sealing agent is used to seal the non polluted coating surface.

After the paint film is dry and solid, the secondary hole sealing treatment shall be carried out.

 

目測

VM


序號

6

工序內容

 

相關照片

 

檢測設備

 

6-1

1.采用專用包覆材料對已檢測合格的輥筒進行包裝。

2.包裝好的輥筒堆放時必須有擺放在防震墊上。

3.工件必須離地存放,不得存放在有潮濕以及腐蝕液體的環境下。

1. The qualified roller shall be packed with special wrapping materials.

2. The packed roller must be placed on the shockproof pad when stacking.

3. the workpieces must be stored off the ground, and shall not be stored in the environment with damp and corrosive liquid.

企業微信截圖_16478313826029.png  

目測

VM

6-2

張貼所需的合格標識。

Post the required qualification mark


Finished



輥?zhàn)訃娡刻蓟u操作流程

Operation Flow of Spraying Tungsten Carbide on Rollers

YATAI



輥?zhàn)訄D號

Drawing No.

XXXX

零件名稱 Roll Name

鍍鋅鋼板輥 Roll

噴涂設備

Spraying Equipment

進口普萊克斯

PRAXAIR from America

設備型號 Equipment Model

JP-5000

熱噴涂類型Spraying type

超音速噴涂Supersonic spraying

技術負責technician

陳國利 Chen Guoli


序號

 

工序內容

Process

相關照片

Photos

檢測設備

TEST

4-1

噴涂必須在前道工序結束后2小時內完成,如超出2小時后還未噴涂,工件必須重新噴砂處理。

The spraying must be completed within 2 hours after the end of the previous process. If the spraying is not finished after 2 hours, the roll srface must be sandblasted again.

時鐘

Clock

4-2

噴涂前使用壓縮空氣吹干凈工件表面Use compressed air to blow the surface of roll before spraying.

 


目測

VM

4-3

1.材料種類:根據圖紙要求選用材料

Material for spraying:

Praxair 1375/H.C STARCK558 or H.C STARCK 519

2.材料規格:Size

  15-53μm


目測

VM

4-4

超音速噴涂參數:

Supersonic spraying parameters

設備型號Unit typeJP5000

載氣量Air carrying capacity29

氧氣量Oxygen quantity1950

煤油量Kerosene quantity6-6.2

噴涂距離distance:300-350mm

送粉powder feeding rate65g/min

超音速噴涂設備(JP-5000

HVOF spraying equipmentJP-5000

4-5

1.使用美國普萊克斯公司生產的JP-5000噴涂設備操作施工。

2.噴涂前再次檢查噴涂工裝是否安裝到位。

3.按規定噴涂參數進行施工。

4.噴涂結束后使用壓縮空氣對工件表面進行清理,去除殘留的灰塵(輥筒兩端點焊配帶試塊留備用和檢測專用)。

1. Use jp-5000 spraying equipment produced by Praxair company to operate and construct.

2. Check whether the spraying tooling is installed in place again before spraying.

3. Carry out the construction according to the specified spraying parameters.

4. After spraying, use compressed air to clean the surface of the roll and remove the residual dust (spot welding at both ends of the roller with test block reserved for standby and testing)

 


4-6

涂層檢驗:

1.涂層厚度要求:根據圖紙用測厚儀檢測。2.涂層表面無飛濺物、無剝落、無開裂。3.涂層厚度均勻。

Coating inspection:

1. Coating thickness requirements: test with thickness gauge according to the drawing.

2. The coating surface shall be free of splashes, peeling and cracking.

3. The coating thickness is uniform.

北京時代T200涂層測厚儀

thickness meter



上一篇:沒有了
下一篇:碳化鎢輥2022-03-14

近期瀏覽:

相關產品

相關新聞

毛化鍍鉻

微信 掃一掃

毛化鍍鉻

手機官網

久久久久香蕉国产线看观看伊| 免费人成年激情视频在线观看| 亚洲日韩中文字幕一区| 国产AV无码国产AV毛片| 亚洲和欧洲一卡二卡三卡| 久久国产精品无码AV影视| 久久久婷婷五月亚洲97色| 少妇被粗大的猛进出69影院| 老熟女hdxx老小配| 欧美老人巨大XXXX做受| 国产精品原创巨作AV| 99无码人妻一区二区三区免费| 亚洲一本一道一区二区三区| 亚洲VA中文字幕无码一区| 国产尤物在线视精品在亚洲| 亚洲AV成人一二三区观看| 色一情一乱一伦一区二区三区日本| 亚洲AV专区无码观看精品天堂| 久久久久噜噜噜亚洲熟女综合| 色五月激情五月| 亚洲乱亚洲乱妇无码麻豆| 又嫩又硬又黄又爽的视频| 久久av无码专区亚洲av桃花岛| 免费观看AV在线网站网址| 欧洲精品卡1区2卡三卡四卡| 免费A级毛片在线播放| 香蕉久久久久久久AV网站| 无码孕妇孕交在线观看| 亚洲 日本 欧洲 欧美 视频| 亚洲国产欧美在线成人| 日韩精品中文字幕无码一区| 黑巨人与欧美精品一区| 亚洲AV成人一区二区三区观看在线| 亚洲人成人无码网www国产| 精品国产乱码久久久久久久小说| 欧美亚洲综合久久偷偷人人| 国产欲女高潮正在播放| 又污又黄无遮掩的网站| 中文幕无线码中文字夫妻| 亚洲乱码无码永久不卡在线| 久久精品午夜福利|